The basic structure of the centrifugal pump is composed of six parts are impeller, pump body, pump shaft, bearing, sealing ring, packing box. 1, the impeller is the core part of the centrifugal pump, its speed is higher than the force, the blade on the impeller plays a major role, the impeller in the assembly before the static balance experiment. The inner and outer surfaces of the impeller shall be smooth to reduce the friction loss of water flow. 2, the pump body is also called the pump shell, it is the main body of the pump. Plays a supporting and fixing role, and is connected with the bearing bracket. 3, the function of the pump shaft is to connect the coupling and the motor, the torque of the motor to the impeller, so it is the main part of the transmission of mechanical energy. 4. Plain bearing uses transparent oil as lubricant and lubricates it to the oil level line. Too much oil to seep out along the pump shaft, too little bearing and overheating and burning cause accidents! During the operation of the pump, the temperature of the bearing is 85 degrees, and the general operation is about 60 degrees.
Winter comes, the air is dry and cold, and the temperature drops to below zero. Are you worried that the water pump in use is easy to freeze or even the pump body is frozen and cracked under low temperature conditions, just like in previous years? In view of this situation, xiaobian summed up the following measures for anti-freezing water pump maintenance. 1, add insulation material for the pump to prevent the pump from freezing; (Water pumps also need to wear "clothes", exposed in the cold outdoor work, we can use cotton wool, towels, waste clothes and other clothes to wrap exposed outdoor water pumps, water pipes, faucets and other water facilities, to achieve thermal insulation effect.) 2, the pump body will not be temporarily empty, when using water, to prevent the pump freezing freezing pump: 3. The doors and Windows of the basement pump room and those without hVAC are closed. The unfinished basement pump room and wind tunnel are blocked. 4. Because all pumps of our company are delivered with hose pressure test, there is water in the pump body and management valve of the factory equipment. If the equipment is not installed, please be sure to take drainage measures to prevent freezing and cracking. 5. If the pump is frozen, do not start the pump. Use hot water or boiled water to pour into the pump to internalize the ice, or heat the pump shell.
The Shanghai Municipal Bureau of Quality and Technical Supervision announced on its website on Monday the results of a random inspection of 70 batches of water pump products in 2015. After the inspection, six batches failed to pass the inspection. According to the introduction, water pump is listed in the national industrial products production license catalogue of products. There are a total of 74 certified manufacturing enterprises in Shanghai, of which 70 have actually received products this time, and another 4 have not received samples due to production suspension and other reasons. According to gb10395.8-2006 "Agricultural and forestry tractors and machinery Technical requirements part 8: Drainage and irrigation pumps and pump units" and other national standards and related standards, the following items of submersible pump products were tested: Overload protection, grounding measures, insulation resistance and electric pump leads to cable and stator winding resistance to voltage, electric pump efficiency, rated capacity at the time of the head, electric pump input power, pump shaft power, power factor, temperature rise within the limit, motor stator cavity water (gas) pressure test, the operation instruction content, sign/sign firmly, production license; The following items of centrifugal pump have been tested: specified point efficiency, specified point flow, head, NPSH, leakage, unit operation, vibration, noise, appearance quality, mark, license mark.
市場分析與洞察:全球智能水泵市場 到2027年,全球智能水泵市場估值將達35.6億美元,在2020年至2027年的報告期內,增長率將達6.80%。全球智能水泵市場報告分析了當前推動這個市場增長的動因,主要在于新興國家與地區數字化程度的不斷提高。 在2020-2027年報告期內,政府對環境能源問題實施的嚴格法規、各終端用戶對泵送系統日益增長的需求、操作靈活性的廣受歡迎,是促進智能水泵市場增長的幾個因素。另一方面,采用智能水泵將進一步增加各種機會,在報告期內推動智能水泵市場的增長。 高資本投資以及小型制造商不采用智能泵系統,將成為阻礙智能水泵在報告期內的市場增長。 本報告詳細介紹了智能泵市場的新發展、貿易法規、進出口分析、生產情況、價值鏈優化、市場份額、國內和本地市場參與者的影響,分析了新興經濟體的機會、市場法規的變化,戰略市場增長分析、市場規模、細分市場的增長、小眾及應用、產品認證、產品發布、地域擴張、市場上的技術創新。
近年來,受到國內良好的投資環境以及基礎建設政策的不斷深化,我國泵閥行業將引來持續增長的發展新機遇。雖然,國內泵閥行業前景樂觀,但也存在一些不利因素。 水泵性能的技術參數有流量、吸程、揚程、軸功率、水功率、效率等;根據不同的工作原理可分為容積水泵、葉片泵等類型。容積泵是利用其工作室容積的變化來傳遞能量;葉片泵是利用回轉葉片與水的相互作用來傳遞能量,有離心泵、軸流泵和混流泵等類型。 鋼鐵作為泵閥產業的原材料,在環境壓力逐漸加大的今天,其亟待轉型。鋼鐵行業將會面臨減產的危險,減產將導致短期內鋼價上調,導致泵閥行業的成本提高,造成泵閥行業短期的價格波動。因此泵閥行業也會受到較大的影響。